Peugeot 405 Manual

Seat belt components - removal and refitting
Bodywork and fittings / Seat belt components - removal and refitting


Note: Note the locations of any spacers and/or washers on the seat belt anchor bolts, to ensure correct refitting.

Front seat belt
Removal
1 Where applicable, remove the cover, then unscrew the lower seat belt anchor bolt from the edge of the seat.

2 Unclip the roof side trim panels to expose the upper B-pillar trim panel top securing screws. Remove the screws (see illustration).

27.2 Removing an upper B-pillar trim panel top securing screw
27.2 Removing an upper B-pillar trim panel top securing screw

3 Prise off the trim plate, and unscrew the seat belt upper anchor bolt (see illustration).

27.3 Removing the trim plate from the front seat belt upper anchor bolt
27.3 Removing the trim plate from the front seat belt upper anchor bolt

Recover the spacer.

4 Working at the bottom of the upper B-pillar trim panel, remove the remaining securing screw, then manipulate the panel from the Bpillar (see illustration).

27.4 Removing the upper B-pillar trim panel lower securing screw
27.4 Removing the upper B-pillar trim panel lower securing screw

5 Unscrew the two now-exposed top securing screws from the lower B-pillar trim panel.

6 Unclip the sill trim panels to expose the lower B-pillar trim panel bottom securing screws. Remove the screws, and withdraw the panel from the B-pillar (see illustration).

27.6 Removing a lower B-pillar trim panel bottom securing screw
27.6 Removing a lower B-pillar trim panel bottom securing screw

7 Unscrew the inertia reel bolt, and withdraw the seat belt assembly (see illustration).

27.7 Front inertia reel securing bolt (arrowed)
27.7 Front inertia reel securing bolt (arrowed)

Refitting
8 Refitting is a reversal of removal, but securely tighten the seat belt securing bolts.

Front seat belt stalk
Warning: On models with seat belt pre-tensioners, do not attempt to remove the seat belt stalk assembly, which
incorporates the pre-tensioner assembly.

Refer the operation to a Peugeot dealer.

Removal
9 Each stalk is secured to the front seat frame by a bolt and washer. Where applicable, remove the trim from the side of the seat for access to the securing bolt.

Refitting
10 Tighten the securing bolt securely.

Rear side seat belts -
Saloon models
Removal
11 Remove the seat cushion and back, as described in Section 26.

12 Unbolt the lower seat belt anchor.

13 Pull the rear quarter trim panel from the side of the body (see illustration). Take care not to break the clips.

27.13 Pull off the rear quarter trim panel
27.13 Pull off the rear quarter trim panel

14 Lift up the rear parcel shelf trim panel to expose the inertia reel.

15 Unscrew the securing bolt, and lift out the inertia reel assembly (see illustration).

27.15 Unscrewing the rear side seat belt inertia reel securing bolt - Saloon
27.15 Unscrewing the rear side seat belt inertia reel securing bolt - Saloon model

16 Slide the seat belt webbing through the slot in the parcel shelf trim panel, then withdraw the seat belt assembly.

Refitting
17 Refitting is a reversal of removal, but securely tighten the seat belt anchor bolts.

Rear side seat belts -
Estate models
Removal
18 Unbolt the lower seat belt anchor from the body.

19 Fold the rear seat back forwards.

20 Working in the luggage compartment, remove the two parcel shelf support panel front securing screws, and unscrew the seat back catch striker (see illustration).

27.20 Remove two front screws (A) and seat back catch striker (B) from the
27.20 Remove two front screws (A) and seat back catch striker (B) from the parcel shelf support panel - Estate model

21 Pull the front end of the parcel shelf support panel away from the body to expose the seat belt inertia reel and the securing bolt (see illustration).

27.21 Rear seat belt inertia reel (A) and securing bolt (B) - Estate model
27.21 Rear seat belt inertia reel (A) and securing bolt (B) - Estate model (viewed with parcel shelf support panel removed)

22 Unscrew the inertia reel securing bolt and withdraw the assembly.

23 Feed the seat belt webbing through the slot in the trim panel, then withdraw the assembly from the vehicle.

Refitting
24 Refitting is a reversal of removal, but securely tighten the seat belt anchor bolts.

Rear centre belt and buckles Removal
25 The assemblies can simply be unbolted from the floor panel, after removing the rear seat cushion (Saloon models) or folding the rear seat cushion forwards (Estate models).

Refitting
26 Refitting is a reversal of removal. Tighten all mounting bolts securely.


© 2018 www.peugeot405.ru. All Rights Reserved.