Peugeot 405 Manual

Centre console - removal and refitting
Bodywork and fittings / Centre console - removal and refitting


Highline console -
models up to 1992
Removal
1 Disconnect the battery negative lead.

2 Move the seats fully rearwards.

3 Where applicable, remove the securing screws, then prise the side panels from the front of the console. Note that the side panels are retained by clips at their top edges.

4 Prise the cassette box from the front of the console, and remove the two now-exposed screws securing the console to the heater panel.

5 Slide the front seats fully forward.

6 Prise out the blanks from each side at the rear of the console, and remove the rear securing screws.

7 Open the lid of the stowage compartment at the rear of the console, and remove the screw from the compartment floor.

8 Remove the two screws (one on each side) securing the console to the gear lever bracket (see illustration).

29.8 Highline centre console fixings - models up to 1992
29.8 Highline centre console fixings - models up to 1992

9 Pull the handbrake lever dust cover from the console (see illustration).

29.9 Removing the handbrake lever dust cover - models up to 1992
29.9 Removing the handbrake lever dust cover - models up to 1992

10 Prise the gear lever gaiter surround from the top of the console, and pull back the gaiter.

11 Lift the console slightly, then disconnect all relevant wiring, and release the wiring harnesses from any clips under the console.

12 Withdraw the console over the gear lever and the handbrake lever.

Refitting
13 Refitting is a reversal of removal.

Lowline console -
models up to 1992
14 The procedure is similar to that described previously for the Highline console, noting the following points.

a) Note that the console is in two sections.

b) Where applicable, ignore the references to the switches.

c) Refer to the accompanying illustrations for the screw locations
Highline console -
models from 1993
Removal
15 Where applicable, remove the front armrest.

16 Prise out the trim plate covering the console centre securing screws. Remove the securing screws.

17 On manual gearbox models, unclip the gear lever gaiter surround from the centre console, then pull up on the gear knob and withdraw the knob/gaiter assembly.

18 On automatic transmission models, proceed as follows.

a) Ensure that the selector lever is in the Neutral position.

b) Remove the two screws from the gear selector lever (one on each side of the lever).

c) Twist the selector lever through a quarter turn clockwise, then pull the pushbutton from the top of the lever.

d) Twist the lever a quarter turn back to its normal position, then pull off the lever.

e) Unclip the selector gate cover.

f) Remove the two securing screws, and withdraw the selector gate assembly.

19 Remove the securing screws, and withdraw the side panels from the front of the console to expose the heater air ducts.

20 Remove the securing screws, and withdraw the air ducts from each side of the console.

21 Working at the front of the console, disconnect the wiring connectors.

22 Fully apply the handbrake, then withdraw the console over the handbrake lever.

Refitting
23 Refitting is a reversal of removal, but on automatic transmission models, refit the selector lever as follows.

a) Ensure that the selector lever is in the Neutral position.

b) Slide the lever over the selector rod, and twist a quarter turn clockwise.

c) Pull the lever up until the top of the lever reaches its stop.

d) Slide the pushbutton into the top of the lever, ensuring that it engages with the groove in the top of the selector rod.

e) Push the lever down, then twist the lever a quarter turn back to its normal position.

f) Check that the pushbutton has locked in position, and check that the button and the lever operate correctly.

Lowline console -
models from 1993
Removal
24 Disconnect the battery negative lead.

25 Move the front seats as far forward as possible.

26 Unscrew the two centre console rear securing screws, then push the seats back (see illustration).

29.26 Unscrew the console rear screws (Lowline console - models from
29.26 Unscrew the console rear screws (Lowline console - models from 1993)

27 Prise the handbrake lever surround/switch panel from the top of the centre console.

Where applicable, disconnect the wiring plugs from the switches in the panel.

28 Pull up the handbrake lever to the fully on position.

29 Prise the ashtray from the housing in the facia centre panel.

30 Open the ashtray cover flap, and pull the ashtray from the housing.

31 Proceed as described in paragraphs 17 and 18 (see illustration).

29.31 Removing gear lever gaiter surround (Lowline console - models
29.31 Removing gear lever gaiter surround (Lowline console - models from 1993)

32 Remove the two now-exposed console front securing screws, then lift the console, and withdraw it over the handbrake (see illustrations).

29.32a Remove the front securing screws . . .
29.32a Remove the front securing screws . . .

29.32b . . . and withdraw the console (Lowline console - models from
29.32b . . . and withdraw the console (Lowline console - models from 1993)

Refitting
33 Refer to paragraph 23.


2018 www.peugeot405.ru. All Rights Reserved.