Peugeot 405 Manual

Bulbs (interior lights) - renewal
Body electrical system / Bulbs (interior lights) - renewal


General
1 Refer to Section 5, paragraph 1.

Courtesy light, glovebox and luggage compartment lights 2 Carefully prise the lens from the light unit.

Note that in some cases, it may prove necessary to prise out the complete light unit to enable the lens to be removed (see illustrations).

6.2a Prising out a courtesy light
6.2a Prising out a courtesy light

6.2b Prise off the lens for access to the bulb
6.2b Prise off the lens for access to the bulb

3 The bulb is a push-fit in the holder.

4 Refitting is a reversal of removal.

Map reading light
5 Prise the map reading light from the roof console.

6 The festoon-type bulb is held between the spring contacts (see illustration).

6.6 Map reading light removed for access to bulb
6.6 Map reading light removed for access to bulb

7 Refitting is a reversal of removal.

Heater/ventilation
control unit illumination bulbs Models up to 1992
8 For access to the bulbs, the control unit must be removed as described in Chapter 11, but note that there is no need to disconnect the control cables from the unit. Once the securing screws have been removed, the control unit can be pulled forwards sufficiently for access to the bulbs without disconnecting the cables.

Models from 1993
9 Disconnect the battery negative lead.

10 Remove the centre console as described in Chapter 11, Section 29.

11 Unscrew the two screws located at the bottom of the ashtray housing.

12 Where applicable, remove the radio/ cassette player as described in Section 20.

On models not fitted with a radio/cassette player, prise out the oddments tray.

13 Remove the two securing screws from the top of the radio/cassette player/oddments tray housing, then withdraw the housing from the facia. Where applicable, disconnect the wiring plug(s) from the rear of the panel.

14 Prise the blanking plate from the top corner of the facia centre ventilation nozzle housing. Remove the now-exposed securing screw.

15 Remove the four housing securing screws located under the heater control panel. Two screws are accessible from the front of the housing, and two screws from underneath.

16 Carefully prise the switches from below the centre facia ventilation nozzles to reveal the remaining housing securing screw.

Remove the screw.

17 Pull the housing forwards, and disconnect the wiring from the clock, then withdraw the housing.

18 Carefully pull the knobs from the heater control levers.

19 Unclip the front panel from the heater control unit to expose the bulbs (see illustration).

6.19 Unclip the front panel from the heater control unit
6.19 Unclip the front panel from the heater control unit

20 The bulbs are a push-fit in the bulbholders (see Haynes Hint).

21 Refitting is a reversal of removal.

Clock illumination bulb
22 For access to the clock illumination bulb, remove the clock as described in Section 11.

Note that on models from 1993, access to the bulb can be gained once the housing has been removed from the facia - there is no need to remove the clock from the housing.

23 To remove the bulbholder, twist it anticlockwise (see illustration). The bulb is integral with the bulbholder.

6.23 Removing the clock illumination bulb - models from 1993
6.23 Removing the clock illumination bulb - models from 1993

24 Fit the new bulb using a reversal of the removal procedure.

Facia switch illumination bulbs 25 The bulbs are integral with the switches, and cannot be renewed independently.

Instrument panel illumination and warning light bulbs
26 Remove the instrument panel as described in Section 9.

27 Twist the relevant bulbholder anticlockwise to remove it from the rear of the panel (see illustration).

6.27 Removing an instrument panel illumination bulb
6.27 Removing an instrument panel illumination bulb

28 The bulbs are a push-fit in the bulbholders.

29 On completion, refit the instrument panel with reference to Section 9.


© 2018 www.peugeot405.ru. All Rights Reserved.